There are multiple types of doorbells available in the market. You can also use the Google Nest Hello video doorbell for your home, which is also secure. Every time someone approaches your home, you’ll receive notifications on your smartphone. With the two-way audio system built in, you can talk and listen to your guests. But sometime facing issues with nest doorbell install.
Your Nest Hello records continuous videos for the past 30 days, so you can see everything that happens in front of your door. In this article, we can discuss the process of how to install a Google Nest Hello video doorbell.
Sometimes users feel the method of Nest doorbell installation is complicated, so here we can tell you the simple process of Nest Hello installation.
Things You Need For Nest Doorbell Installation
You will need an existing doorbell with compatible wiring and a transformer with the appropriate voltage before you can start the nest doorbell installation. At the installation location, there is a need for a steadfast WiFi connection. A power drill and screwdriver are also required. These products are essential for learning how to install a Google Nest Hello video doorbell. Here you can get detailed information.
Your Current Doorbell
You will need to replace a working doorbell to install a Nest Hello video doorbell. Certain doorbells, including those with intercom buttons, front gate controls, and other advanced controls, aren’t compatible with Nest Hello. Sometimes users don’t have an existing doorbell, so there is a need to buy a compatible doorbell with your Google Nest Hello video doorbell. It is also vital for the nest doorbell install.
Compatible Doorbell Wiring
Nest Hello works with most doorbells but requires 14 to 30 Volt wires. A multimeter is used to check the voltage of your doorbell’s wiring.
Compatible Transformer
A doorbell transformer must provide 16 to 24 volts (V) and at least 10 volt-amps (VA). Your doorbell transformer is located near your electrical panel. In addition to garages, HVAC systems, utility rooms, and doorbell chimes, it might also be located in your utility room.
Doorbell Chime
There must also be a chime on your doorbell with a voltage between 14 and 30 volts. Your chime will likely work with Nest Hello if it has two or more wires. Nest Hello cannot work if you only have batteries and no wires.
Reliable WiFi Connection
Make sure you have a reliable WiFi connection before the Nest doorbell installation. For a video doorbell to work, you need an upload speed of at least 2 Mbps. There is also a need to use accurate WiFi passwords so it works perfectly.
Tools
You will need a power drill and a Phillips head screwdriver to install your Nest Hello Video Doorbell.
How to Install a Google Nest Hello Video Doorbell or Nest Doorbell Install
It is necessary to know the proper steps for how to install a Google Nest Hello video doorbell. Download the Nest app onto your smartphone to install a Nest Hello doorbell. There is a need to turn off your existing doorbell and install the chime connector in your chime box. Connect your wiring, attach your wall plate, and remove your old doorbell. Last but not least, attach the Nest doorbell. Here you can check the steps below for the Nest Hello install.
Download & Install Google Nest App
It is a vital step for Nest doorbell installation to download and install the Google Nest app. You can quickly download it from the Google Play Store and the Apple App Store. To use the app, you have to sign in with a Google or Nest account.
You will need a Google account if you don’t have either. Go to gmail.com and click the blue “Create an account” button in the top-right corner of the page to create a new Google account.
Click on Add Product
Add your Nest Hello device by tapping the plus sign. If you already have a Nest account, you can tap the gear icon in the top-right corner. You can scroll down and choose to add a product.
Scan QR Code
On the back side of the Nest Hello, you will see the QR code printed near the bottom. Your Nest Hello box also contains a QR code that can be scanned. You can use the blue square inside the app to move your smartphone or tablet’s camera closer to the code by placing it at least a foot away from it. Once the QR code is detected, the square will turn green. Sometimes users face issues scanning QR codes, but you can also enter them manually. Here, you can tap on Continue without scanning the device. Enter the six-character key located below the QR code.
Perform the Compatibility Checker
You can quickly skip this step by clicking on Next.
Turn the Power Off of Your Current Doorbell
Your doorbell and chime are disconnected from your circuit breaker. Ring your doorbell to see if it’s off.
Remove Your Chime’s Cover
Near your door, your doorbell chime is mounted high on the wall. Depending on your model, you can either snap off the plastic cover or unscrew it first.
Choose Chime Wire Configuration in the App
It is also vital to check your wire configuration. Choose the number of wires connected to your terminal. After that, tap on the proper labeling setup, which you can see on your chime. You will be able to see which wire you need to remove in the next step. After deciding whether you need a new doorbell for your front or back door, you can proceed.
Disconnect the Wire
Use a screwdriver to make the screw on the wire that the app tells you to remove loose. It is crucial to remove the wires gently and also blend them properly.
Strengthen the Wire
It is also necessary to straighten the ends of the wires properly. Make sure to twist any loose wires together in a single line if your chime has them. There is a need to have ¼ inch of uncovered wire, and you can trim the excess wire.
Remove the Chime Connector from the Box
It is also vital to remove the chime connector from your box. You will receive a gray chime connector with your Nest Hello. Two wire hooks and two small clips will be attached to short cables.
Push the Wire
There is a need to push the wire into the chime connector wire clip. Push the end of the wire you removed into the small hole at the end of the chime connector. There is a need to push it until it stops. Give the wire a gentle tug after releasing the tab on the clip.
Screw the Wires
It is also necessary to screw the wire onto your chime connector. Here, you can also check from your app which wire of your chime connector is attached to the terminal screw of the chime. After this, you can disconnect the wire from your chime. Push the wire firmly into the clip of the remaining chime connector.
Mount the Chime Connector
- It is critical to mount the chime connector in your chime box.
- You can place it inside your chime box if there is enough room.
- Your chime box can also be placed on the outside if you prefer. To mount the chime connector to your chime box, remove the adhesive tape from the back side and press it firmly.
- Ensure that the connector, wires, or any moving parts do not touch the chime. You may not be able to hear it correctly or it may not work at all. After this, you can put the cover back on the chime box.
Remove Your Old Doorbell
It is time to remove your old doorbell with help of a Phillips head screwdriver. You can remove all the wires and unscrew your current doorbell. Afterward, pull the cords back and twist them or secure them to the wall, to keep them from slipping back into the gap.
Mark the Screw Holes
- Here you can mark the holes for the wall plate.
- On the wall plate provided, the doorbell wire can run through the bottom half of the center hole.
- Mark the location of the screw holes on the wall or surface with a pencil.
- Ensure that the Nest logo is upright. You are not able to lock your Nest doorbell otherwise.
After this, there is a need to drill your pilot holes. Take off the wall plate and use a 3/32nd drill and make a hole where you marked the screw holes in the wall plate.
Screw The Mounting Plate
Now it is time to screw the mounting plate into the wall. It is imperative to make ensure that the Nest logo is on the upright. The wires run through the lower part of the wall plate opening.
Attach Wires With Nest Hello Doorbell
- It is time to connect wires with your new Nest Hello Doorbell. You can wrap each wire around the Nest Doorbell’s screws.
- Each wire is tightened by tightening screws. No matter which wire goes to which screw, it doesn’t matter what wire goes first.
- Ensure that exposed wires don’t touch each other. Make sure the wires are pointed downward, so you can neatly tuck away the excess wiring in the wall. Connect the doorbell to the wall plate, then thread your wires back into the wall.
There is a need to push the excess wires into the wall and also move your doorbell closer to the mount. - The Nest doorbell top is inserted into the mounting bracket. You can snap it into place.
- Lastly, press down on the bottom until it clicks. Remove the doorbell from the wall plate if you don’t hear a click. Try again after tucking any excess wiring into the wall.
Turn the Power Back On
There is a need to turn on the power back. The Nest doorbell should also work once the power is switched back on. There will be a melody-like sound emanating from the light ring as it glows blue. Check the wiring of your chime box if it doesn’t light up. The yellow light indicates that your doorbell is not receiving enough power to stream video. To reconfigure your doorbell voltage, Nest recommends you contact a professional installer.
Complete the Setup With the App
There is a need to complete the setup with the help of an app. In the app, select the location where you installed your Nest doorbell. Select your WiFi name and enter your WiFi password to connect the Nest Hello to your network. Your doorbell camera is now visible when you tap Next on the screen that says, “Added to your Nest account.”
Test Your Nest Hello Doorbell
After completing the process of the Nest doorbell installation there is a need to test whether your doorbell is working properly or not. Now the app also notifies you that someone is at your door. Using the in-app slider, you can adjust the duration of an electric chime without moving parts so you can hear it ring.
Take off the chime cover if your mechanical chime does not sound right or does not work at all. Make sure the chime connector is not touching anything moving.
Final Words
When the process of Nest doorbell install is complete there is a need to sign up for Nest aware. It is the Nest video storage subscription. Here you can choose your language and enable the audio recording. It is also necessary to follow all steps accordingly Nest Hello install.
Read Also: Get the Solution on Firestick Won’t Turn On